To choose a wing foil wing, start with your weight and the wind, then adjust for where you ride and the rest of your gear. For 15 knots of wind, count on 4 m² under 65 kg, 5 m² for 80 kg, and 6 m² above 95 kg. An 80 kg rider starts well with a 5 m² wing, a 1750 cm² foil, and a beginner board, in 12 to 18 knots. Only after that come the criteria that separate two wings of the same area: the bladder pressure, the leading edge material, the type of handles, and the profile.
What wing size do you need for your weight and the wind?
A wing's area is first read as a wind range. The larger the wing, the more power it catches in light wind, and the faster it becomes unmanageable when it blows. Here are the real ranges of our V4 range, for a 75 kg rider on a medium-sized foil.
| Size | Wind range | Main use |
|---|---|---|
| 2.8 m² | 23 to 40 knots | Strong wind and storm |
| 3.4 m² | 18 to 33 knots | Strong wind |
| 4.0 m² | 14 to 30 knots | Sustained wind, smaller builds |
| 4.5 m² | 12 to 28 knots | All-round, lighter builds |
| 5.0 m² | 10 to 25 knots | The reference size for beginners |
| 6.0 m² | 8 to 20 knots | Light wind, heavier builds |
| 7.0 m² | 7 to 18 knots | Extreme light wind |
These ranges shift with your build. A 95 kg rider reads the table one size up, a 60 kg rider one size down. Skill level matters too: a beginner should stay in the middle of the range, where the wing is easy to handle, rather than at its extremes, where you have to manage overpowered or underpowered conditions.
What wing size for 15 knots of wind?
Fifteen knots is the most common wind for wing foiling. Here is the wing size to plan for based on your weight, for a rider on a medium-sized foil:
| Your weight | Wing for 15 knots |
|---|---|
| Under 65 kg | 4 m² |
| 65 to 75 kg | 4.5 m² |
| 75 to 85 kg | 5 m² |
| 85 to 95 kg | 5 to 6 m² |
| Over 95 kg | 6 m² |
A beginner should rather choose the upper end of the range, as it takes off earlier. On a high-altitude lake, take one size up.
Why location matters as much as your weight
This is the criterion almost nobody mentions, yet it changes the answer. At the same displayed wind speed, a wing does not pull the same way depending on where you ride, because it is air density that produces power, not wind speed alone.
In the mountains or at altitude, the air is drier and less dense, so it carries less load. Fifteen knots on a high-altitude lake does not deliver the power of fifteen knots on the coast of Brittany, for example. You have to compensate with more area, often half a size to one size above what you would take on the coast.
The water body plays in the same direction: steady, clean wind is easier to use than gusty, shifting wind, where you need a margin so you don't end up underpowered between two gusts. So where you ride has an enormous influence on your gear choice.
A wing is never chosen on its own
The most common mistake is to think about the wing as if it were independent of everything else. In wing foiling, the power that lifts you out of the water comes from three elements that balance each other: the wing, the foil, and the board.
A small-area foil generates less lift: you then need more wing area, or more wind, to take off. Conversely, a large foil takes off very early and lets you ride with a smaller wing than the table suggests. Same logic for the board: volume and length get you up early and compensate for a wing that is slightly undersized.
This is why our reference setup for beginners is sold as a complete system: 80 kg, 5 m² wing, 1750 cm² foil, and beginner board, in 12 to 18 knots. Change one element and the ideal wing size moves. For details on board volume, our guide to board size by weight complements this one.
The bladder: the least known criterion, yet the most decisive
The structure of a wing foil wing relies on two inflatable bladders: the leading edge and the central batten. Their diameter and above all their inflation pressure, expressed in PSI, directly determine the wing's stiffness, and therefore its responsiveness and its ability to keep its shape under load. A wing that deforms in flight loses power and becomes harder to control, whatever its announced size.
Bladder diameter is correlated with the pressure you can put into it and with the material used. The higher the allowable pressure in the leading edge, the more you can reduce the diameter of the bladder sections to gain glide and reduce drag. This principle applies to all wing foil wings, regardless of brand.
The leading edge material directly governs this pressure: a fabric such as Dacron requires a larger diameter (because it tolerates less overpressure), while a more technical material such as aramid withstands higher pressure for a reduced diameter. The recommended pressure generally decreases with size: the larger the wing, the longer its structure, and the more you need to slightly reduce pressure so as not to overstress it.
As an example, here are the recommended pressures on our V4 range (Dacron), by size:
| Size | Leading edge (max PSI) | Central batten (max PSI) |
|---|---|---|
| 2.8 to 4.0 m² | 8-8.5 | 8.5 |
| 4.5 to 5.0 m² | 7.5-8.5 | 7.5 |
| 6.0 m² | 7-8 | 8 |
| 7.0 m² | 6.5 | 6.5 |
On our V4 Elite, with an aramid leading edge, the recommended pressure rises to 11 PSI regardless of size, with a bladder diameter reduction of nearly 17% compared with the V4. This is a good illustration of the principle above: more technical material, higher pressure, finer diameter, which means better glide, better pointing, less weight, and more responsiveness.
A reliable high-pressure pump is therefore not a minor detail: without one, it is impossible to reach the recommended pressure and fully exploit a wing's stiffness, whatever its brand.
Leading edge material: Dacron or aramid
The leading edge is the main bladder that gives the wing its shape. Two material families share the market.
Dacron is the most widespread material. It offers good performance characteristics at an accessible price, with good durability. It is the choice for our V4.
Aramid is a more technical material: it allows higher pressure and therefore greater stiffness for a reduced diameter, which lowers drag. The trade-off is a higher price. It is the choice for our V4 Elite, in P85 reference, that is 85 g/m².
A third family exists at the high end of the market: Aluula-type composites, used by several brands on their most expensive models. They pursue the same goal as aramid: more stiffness for less weight, at a significantly higher price but with characteristics similar to aramid.
Handles: rigid or boom
Two gripping systems exist on the market: rigid handles and the boom (or wishbone).
Rigid handles offer direct control and good power transmission, which makes pumping and maneuvers easier. They are standard equipment on the vast majority of wing foil wings, including our entire V4 and V4 Elite range.
The boom is a rigid tube that runs along the entire length of the central batten, much like a sailboard wishbone. It lets you grab the wing anywhere along its length rather than at fixed points, which helps maintain power in light wind, release one hand without losing control, and surf a wave with a central grip. On the downside, it is generally a bit less rigid than a set of rigid handles. On our V4 rigid handles, only about ten centimeters of the batten cannot be gripped: the grip difference with a boom therefore remains small, the boom's advantage lying mainly in grip versatility and the rigid handles' advantage in packing into the bag. The boom is available as an option on our V4 Elite.
One point to check before buying, whatever the brand: several manufacturers now sell the wing bare, with handles and boom charged separately. The displayed price gap between two models therefore means little until you have compared what is actually included.
Profile and canopy
The profile, that is the wing's camber and the tension of its trailing sheet, determines its behavior in flight. Some wings take off very early but top out quickly in speed, others are designed to go fast: this is a design choice specific to each brand and each range. At SROKA, the V4 aims for versatility, taking off relatively early while keeping good speed sensations, whereas the V4 Elite pushes further toward performance.
The canopy is the fabric that forms the wing's surface. The thicker it is, the stiffer and more durable it is, but also the heavier: it is a trade-off between weight, stiffness, and durability, not a criterion where more is automatically better. On our V4 Elite, for example, the weight saved by reducing bladder diameter was reinvested in a thicker canopy: the wing lasts about twice as long and deforms less over time.

One wing or a quiver of several sizes?
To start, one wing is enough, and it is even preferable: you learn to fly on constant gear, without wondering at every session whether your problem comes from you or from the size you chose.
As soon as you ride regularly, a single wing becomes limiting. You don't go out when there is too little wind, and you get knocked around when there is too much. At this stage, you need two to three sizes: a large one for light wind, an intermediate size that covers most sessions, and a small one if you really want to ride in strong wind.
The gap between two neighboring sizes should remain consistent. A step of 1 to 1.5 m² between two wings covers the range well without leaving a gap or creating unnecessary overlap.
How SROKA wings compare with other brands
The most useful comparison is not about sizes, which all brands offer in similar ranges, but about the leading edge construction and bladder section diameters, about what is included in the price, and about the real price.
| Model | Leading edge and fabric | Handles | Observed prices |
|---|---|---|---|
| SROKA Wing V4 | Dacron | Rigid handles included | 720 to 920 € |
| SROKA Wing V4 Elite | Aramid P85, 85 g/m² | Rigid handles included, boom optional | 1,029 to 1,179 € |
| GONG Droid Aramid 2026 | UPE Aramid 85 g/m², triple ripstop canopy 54 g/m² | Boom sold separately | From 719 to 1199 without boom |
| Duotone Unit 2026 | MOD3 S canopy | Handles or Fusion boom sold separately | from 1,019 € |
| Duotone Unit SLS 2026 | PentaTX with Aluula Gold central panel | Handles or Fusion boom sold separately | around 1,269 € |
| F-One Strike V6 2026 | High-tenacity HITEX polyester, Aluula 103 g version | Soft, hybrid or rigid handles, carbon boom compatible with several sizes | from 989 € |
| Ozone Flow V2 2026 | Teijin hybrid canopy | One-piece carbon boom | around 1,229 € |
| Naish ADX 2026 | Radial construction with double luff panel, Nvision version in Aluula 82 g/m² | Removable short or long handles, carbon boom optional | from 899 € |
Prices noted at French and European resellers in September 2026, for information only and subject to variation by size and model year.
Two takeaways emerge from this table. First, the 85 g/m² aramid we use on the V4 Elite is exactly the weight chosen by GONG for its Droid Aramid range, the top of its wing catalog. You are therefore on the same material family as the market's premium, at a price that stays below most models with comparable construction. Second, the question of handles: for several brands, the wing is sold bare and the handle set or boom is added to the bill. Our rigid handles are included, on the V4 as on the V4 Elite.
Why a wing bursts: causes and failure points
A bladder that bursts is almost never a manufacturing defect: it is most often a combination of avoidable causes. Understanding the mechanisms helps you protect your gear, whatever the brand.
Sun overheating is the most frequent cause. An inflated wing left in full sun, on the sand or in a car, sees the air inside the bladders expand under the heat. The pressure then rises on its own, without anyone touching the pump, and can exceed the material's limit.
Overinflation is more direct: exceeding the maximum recommended PSI for the wing size puts the structure under stress it was not designed to withstand.
Material fatigue works over time. UV, salt, and repeated friction gradually weaken the fabric and the seams. An old wing can burst at a pressure it handled without problems when new.
A localized impact, a crash, contact with a rock, a board or the foil, creates a point of weakness. It is often the starting point of a tear that then spreads under pressure.
Leaning on your wing like a cane during a fall puts enormous overpressure into the bladders and can cause an explosion.
The most common failure points follow a logic of stress concentration: the seams, the most mechanically stressed area; around the inflation valve; the bladder itself in case of overpressure, more exposed on reduced diameters such as aramid, which offers less margin; and the leading edge at the handle attachment point, another area of high stress.
One simple habit limits the risk: slightly deflate a wing that has to stay in the sun rather than leaving it at full pressure.
Know that all wings on the market are tested and inflated for 48 hours to check that the wing has no defects.
Summary: where to start
| Your situation | What we recommend |
|---|---|
| You are a beginner, around 80 kg, seaside | A V4 in 5.0 m², with a 1750 cm² foil and a beginner board, for 12 to 18 knots |
| You are a beginner and weigh noticeably less or noticeably more | Move up or down one size: 4.5 m² for a lighter build, 6.0 m² above 95 kg |
| You ride on a high-altitude lake or in the mountains | Take one size up from what you would choose on the coast |
| You ride regularly and want to get out more often | Add a second size, keeping a 1 to 1.5 m² gap |
| You are looking for performance and longevity | The V4 Elite, aramid leading edge at 11 PSI, reinforced canopy, boom available as an option |
Choosing between our two ranges comes down to weighing these criteria against your level and your practice: our wing foil wings and their detailed technical sheets are available in our dedicated collection.
FAQ: choosing your wing foil wing
What wing size for 15 knots of wind?
For 15 knots, plan on a 4 m² wing under 65 kg, 4.5 m² from 65 to 75 kg, 5 m² from 75 to 85 kg, 5 to 6 m² from 85 to 95 kg, and 6 m² above 95 kg. Beginners should go for the upper end of the range, and one size up on a high-altitude lake.
What wing foil wing size should a beginner choose?
A 5 m² wing suits a rider weighing about 80 kg in 12 to 18 knots, paired with a 1750 cm² foil and a beginner board. Go one size smaller for a light build, and one size larger above 95 kg.
Do you need several wing foil wings?
One is enough to learn. Once you ride regularly, you need two or three sizes to cover the real wind range of your spot, with 1 to 1.5 m² between two wings.
Why do you need a bigger wing in the mountains?
Air at altitude is drier and less dense, so it generates less lift. At the same displayed wind speed, the actual power is lower than at sea level, which requires more surface area.
Why does the pressure of a wing foil wing matter?
Pressure determines the wing's rigidity. A well-inflated wing keeps its shape under load, transfers power better, and responds more precisely. An underinflated wing deforms in flight and loses performance, whatever its size.
Should you choose rigid handles or a boom for wing foil?
Rigid handles offer direct control and suit most riding styles. A boom lets you grip the wing anywhere along its length, which is useful in waves and light wind, at the cost of slightly lower rigidity and a little extra weight.
What is the difference between Dacron and aramid on a wing foil wing?
Dacron is the standard material: durable and affordable. Aramid is thinner and stiffer, reduces drag, and withstands higher pressure, but it costs more.
Does the foil size change which wing size to choose?
Yes. A small foil generates less lift and requires more wing surface or more wind to take off. A large foil gets up earlier and lets you ride with a smaller wing.
Why can a wing foil wing burst?
Most often because of overheating in the sun, which raises the pressure on its own, over-inflation beyond the recommended PSI, material fatigue with age, or a localized impact. The tear usually starts at a seam, the valve, or an attachment point.
About the author
Bruno Sroka, triple world champion, quadruple European champion and triple French champion in kitesurfing. Crossed Cape Horn by kitesurf (2008), set the English Channel record (2012), and completed the 444 km (240 nautical miles) France-Ireland crossing in 16 h 40 min (2013). Former PE teacher, founder of SROKA Company, a Breton brand of foil, wing foil, SUP and parawing. Designer of the PushBar System® with Gaël Contal, SROKA ambassador and originator of the sheet in / sheet out (sheeting) concept. SROKA wings are designed and tested in Brittany by Bruno and his team.


