Skip to content
Cart 1
Aller au contenu principal

Parawing fabric weight: why the lightest is not necessarily the best choice

A very fine Parawing fabric flies better on day one. But what's it worth at the hundredth session? Weight, coating, porosity: what the Parawing has been measuring for years, and what it changes for your beach sessions.

Durabilité du tissu de parawing : grammage de la toile et tenue du profil dans le temps
    Bruno Sroka
    Publié le Mis à jour le
    13 min de lecture

    The lightest fabric is not necessarily the best choice for a parawing. A very thin ripstop flies better when the wing is new, especially in light wind. But it has less material to lose: as it ages, its coating wears down, the fabric stretches along the bias and the profile deforms. The wing then needs more wind to get going. A 30 g/m² fabric ages more slowly and keeps its low end of the wind range for longer.

    FYNIX SROKA parawing wing in 30 g/m² high-tenacity ripstop

    For two seasons now, the parawing market has been chasing grams. Fabrics keep getting thinner, "ultralight" materials borrowed from paragliding are showing up on wings, and the total weight of the wing has become the number one sales argument. That is understandable: a light parawing takes off early, packs down small and stays up when the wind drops.

    But one question is missing from the debate. How does this wing hold up after one season? After two seasons? After a hundred sessions?

    At SROKA, we chose not to go below 30 g/m² on the FYNIX. This is not a default choice, nor a technological lag. It is a deliberate trade-off, based on what we have seen in kitesurfing and wing foil, and on what the paragliding world has been measuring for years with rigorous protocols that the watersports industry has still not adopted.

    Here is why.

    What does fabric weight really change in flight?

    Let's be honest from the start: lightweight fabric has real advantages, and denying them would make no sense.

    Unlike an inflatable wing, which holds its shape thanks to its inflated leading edge and central bladder, a parawing relies entirely on the apparent wind to keep its shape. There is no bladder, no batten, no frame. The shape of the wing is the fabric, the bridle and the wind pressure.

    In that logic, a lighter fabric brings:

    • better hold in the air when the wind softens;
    • easier relaunch after a crash;
    • better responsiveness to the controls;
    • less inertia in maneuvers.

    The benefit is especially visible in light wind, where a heavy wing tends to collapse or lose its shape.

    In other words: on a new wing, static, in a one-day comparison, the thinnest fabric almost always wins.

    The problem is that nobody tests wings at the hundredth session. And that is exactly where everything is decided.

    How does paragliding measure fabric wear?

    Paragliding is considerably ahead of us. Because the pilot's safety depends directly on it, the sector has long had protocols for measuring the condition of the fabric, with inspection workshops and quantified criteria.

    The reference instrument is called a porosimeter. The principle is simple: a defined volume of air is pushed through the fabric and the time is measured. In practice, we measure the time needed for 0.25 liter of air to pass through about 40 cm² of fabric at a pressure of 10 millibars. The result is expressed in seconds and can be converted into liters per square meter per minute.

    The thresholds used by inspection workshops are telling. New fabric takes several minutes. Below 30 seconds, the canopy is subject to a recommendation for caution regarding its behavior in flight. Around 10 seconds, depending on the workshop, it is considered unserviceable: it is no longer fit to fly.

    These measurements are taken at several points, typically five, distributed from the center toward the tips, on the upper surface, at about 20 to 30% of the chord from the leading edge. That is where the fabric works hardest.

    But the most important point for us is not the number. It is the mechanism.

    Weave and coating: what really wears out

    Sail fabric is not just a weave. It is a weave plus a coating. And this coating degrades in two ways: mechanically, through repeated folding, friction, sand and the tension experienced in flight; chemically, mainly under the effect of UV and humidity.

    Now, and this is the heart of the matter, the coating does not only serve to make the fabric airtight. It also stiffens it, particularly along the bias, that is, diagonally to the warp and weft threads. This is exactly the direction in which a flexible wing works.

    The consequence is direct and documented: a porous sail deforms. It becomes slower, its stall comes closer, and in extreme cases it can adopt degraded aerodynamic behavior.

    Diagram of parawing fabric bias: warp and weft threads, and the diagonal where the wing deforms as the coating wears

    It is not the fabric that breaks, it is the fabric that loses its stiffness. And when it loses its stiffness, the shape of the wing moves, with direct consequences on the water.

    Why does a kite or wing eventually get tired?

    Watersports have no porosimeter, but they have something else: twenty years of field experience.

    In kitesurfing, the race for ultra-thin fabric has already happened. The observation from riders and workshops has been the same everywhere: overly thin fabrics stretch quickly. The fabric slides along the bias, the profile hollows out, and the wing no longer behaves as it did on day one. Not because it is punctured, but because it has moved.

    In wing foil, the phenomenon is even more telling, because everyone has experienced it. After a season or two of heavy use, a wing becomes soft. The trailing edge starts to flutter. The wing points less well upwind, or its ability to work in light wind is impaired. The rider feels the wing is tired, without being able to put a technical word to it. And when they unfold it on the beach, the fabric looks intact. No tear, no hole, nothing visible.

    It is the same mechanism measured in paragliding, simply without an instrument to quantify it. The sign to watch is the trailing edge: if it is slack and starts to flap, the fabric has begun to work and the wing to deform.

    The parawing is exposed to the same phenomenon, and worse. Because it has no inflated structure, absolutely everything relies on the fabric holding its shape. And because its environment is more aggressive than that of paragliding: salt, sand, immersion, humid packing in a bag, unpredictable drying.

    What happens when a parawing's fabric stretches?

    A wing does not die when it tears, it dies when it deforms. We need to be precise about what this deformation produces, because it is often misunderstood.

    When the fabric stretches and the profile hollows out, the wing does not become more powerful. It is the opposite. The profile no longer holds properly, the wing no longer loads up as it should, and it generates less power than it did originally. It also reacts less to bar inputs.

    The practical consequence is very concrete: you now need more wind to get going. The bottom of the wind range moves up. Take an example, with an identical setup: the wing that got you up in 12 knots now needs 14 or 15. You still have the same wing in the bag, the same announced area, but you have lost the most valuable sessions: those in light wind. Your takeoff threshold depends on your whole system (wing, foil, board, level), as we explain in our article on the minimum wind for parawing.

    This is exactly what riders describe when they say their wing is tired.

    And this is where the real problem of the market lies. At the moment of purchase, you have no way of measuring this. No porosimeter, no history, no protocol. You have a single figure that can be compared from one brand to another, when it is displayed: the fabric weight and the weight of the wing.

    As a result, the whole market is pushed toward ultra-thin by a criterion that only measures the first day of use.

    15, 20, 30 or 50 g/m²: which fabric for which use?

    Fabric weight is neither good nor bad in itself. It shifts the compromise between day-one performance and durability. This table summarizes that compromise.

    Criterion Very thin fabric (15 to 20 g/m²) 30 g/m² fabric
    Weight of the wing Lighter Slightly heavier for the same area
    Flight in light wind, new wing Advantage Slightly behind
    Margin before the coating wears Low More material, slower degradation
    Profile hold over sessions Stretches faster along the bias Holds for longer
    Bottom of the wind range over the seasons Moves up faster Moves up more slowly
    Sand, salt, repeated folding More sensitive More resistant
    Who is it for? Pure downwind, absolute priority on weight, rider who renews their wing often Freeride, intensive use, sandy spots, rider who keeps their wing for several seasons

    At the other end of the scale, some brands use 50 g/m² fabrics. They gain even more robustness, but the wing becomes noticeably heavier for the same area and loses its advantage in light wind, where the parawing makes the difference. For the FYNIX, 30 g/m² is our balance point between these two extremes.

    Fabric weight alone does not tell the whole story. At equal weight, yarn quality, weave density and the type of coating make a big difference: a thick entry-level ripstop, chosen for its price, has nothing in common with a well-coated 30 g/m² fabric. This is why the question of coating is among the buying criteria listed below.

    Naturally hydrophobic 30 g/m² ripstop fabric of the FYNIX SROKA parawing

    Why does the FYNIX use a 30 g/m² fabric?

    The FYNIX uses a 30 g/m² ripstop fabric, naturally hydrophobic.

    Let's state it clearly: this choice has a cost. For the same area, a 30 g/m² fabric weighs more than a 20 or 15 g/m² fabric. On a comparative spec sheet, we will not be the lightest parawing on the market. We accept that, and we prefer to explain it rather than hide it.

    What this choice brings in return:

    • More material in the weave and in the coating before the fabric really starts to work along the bias. Degradation exists, it is unavoidable, but it is slower.
    • Better profile hold over time, so a wing that keeps its ability to load up and get going early for longer.
    • A low end of the wind range that moves up more slowly over the seasons. In other words, the wing you use two seasons later still resembles the one you bought.
    • Better resistance to the aggressions of the marine environment, sand and repeated folding.

    At 15 g/m², there is essentially the yarn and a thin coating layer: very little margin before the fabric loses its stiffness. At 30 g/m², there is material.

    The FYNIX is still young, and we do not have two seasons of hindsight on this specific model. This choice is based on what we have seen age in kitesurfing and wing foil, and on the mechanism measured in paragliding.

    This is not an automatic superiority, it is a positioning: we optimize performance over the wing's lifespan, not performance on day one.

    How do you slow the aging of your parawing?

    Whatever the fabric weight, lifespan depends enormously on use and storage. A wing stored wet or left in the sun will degrade faster than a wing used often but properly dried and stored. UV and residual humidity are the main enemies of the coating.

    • Do not rub your wing when it is full of sand: sand acts as an abrasive on the coating.
    • If your wing is wet, let it dry thoroughly before storing it.
    • Never fold it the same way every time, and avoid sharp creases: repeated in the same place, they create lines of weakness in the fabric.
    • Do not let it flap in the wind on the beach: every flap works the fabric for nothing.
    • Do not leave it in full sun: UV weakens the fabric and its coating.

    All the steps, one by one (drying, folding, storage, checks), are detailed in our guide to maintaining a parawing.

    FYNIX parawing drying in the shade after a session

    How do you assess a parawing before buying it?

    A few useful questions to ask, whatever brand you are considering:

    • What is the exact fabric weight, and what type of coating is used?
    • Does the manufacturer have data or field feedback on the condition of its wings after one or two seasons of intensive use?
    • Is there a repair and inspection service, and what exactly does it check?
    • What do riders who have used the model for more than a year say, not just the launch tests?

    And above all, keep the right reflex: do not judge a wing on its displayed weight, judge it on what it will be worth at your hundredth session.

    The fabric is only one criterion among others: size, foil, board and your program matter just as much.

    The FYNIX is the first parawing with true dynamic sheet in / sheet out thanks to the PushBar System® (registered trademark, patent pending). Discover the FYNIX SROKA parawing and its 30 g/m² fabric, or browse the full SROKA parawing collection.

    Frequently asked questions about parawing fabric

    Which fabric weight should I choose for a parawing?

    There is no absolute good weight. A very thin fabric, 15 to 20 g/m², flies better when the wing is new, especially in light wind, and packs down smaller. A 30 g/m² fabric is a little heavier but keeps its profile for longer. Some brands go up to 50 g/m², at the cost of a noticeably heavier wing. Choose according to your program and the number of seasons you plan to keep the wing.

    Is a light parawing more fragile?

    Not necessarily when it comes to tearing. But a very thin fabric has less margin before its coating wears. The fabric then stretches faster along the bias, the profile deforms and the wing loses power.

    How can I tell if my parawing fabric is tired?

    Look at the trailing edge: if it is slack and starts to flap, the fabric has begun to work. On the water, the wing needs more wind to get going, loads up less well, responds less to the bar and relaunches less easily after a crash.

    Why does a worn wing need more wind?

    Because its profile hollows out and no longer holds. The wing loads up less well and generates less power than it did originally. The bottom of the wind range moves up, even though the area of the wing has not changed.

    What is the fabric weight of the FYNIX?

    The FYNIX uses a 30 g/m² ripstop fabric, naturally hydrophobic. SROKA chose this weight to favor profile hold over time rather than minimum weight on day one.

    How can I extend the lifespan of a parawing's fabric?

    Dry it before storing it, avoid leaving it in the sun, do not rub it when it is full of sand, vary the location of the folds and do not let it flap in the wind on the beach.

    Portrait of Bruno Sroka, founder of SROKA Company

    Bruno Sroka, three-time world champion, four-time European champion and three-time French champion in kitesurfing. Kitesurfing crossing of Cape Horn (2008), English Channel record (2012), France-Ireland crossing of 444 km (240 nautical miles) in 16 h 40 (2013). Former PE teacher, founder of SROKA Company, a Breton brand of foil, wing foil, SUP and parawing. Designer of the PushBar System® with Gaël Contal, SROKA ambassador and originator of the idea of sheet in / sheet out.